Display the SPB-PIM Gateway Multicast Routes

Use the following procedure to display the SPB-PIM Gateway multicast routes. This procedure displays upstream (toward the foreign source) information and downstream (receiver) information on the SPB-PIM Gateway interfaces. This command does not display the following information:

Upstream information for streams ingressing on spb-multicast interfaces
Upstream information for streams ingressing from a remote SPB node
Receivers in spb-multicast interfaces

Use the show isis spbm ip-multicast-route command to display information on all multicast streams and the multicast streams ingress interfaces and egress interfaces.

Use the show ip spb-pim-gw mroute command to display information only on SPB-PIM Gateway interfaces.

Procedure

To enter User EXEC mode, log on to the switch.
Display the SPB-PIM Gateway multicast routes:

show ip spb-pim-rw mroute [source {A.B.C.D}] [group {A.B.C.D}] [vrf WORD<1-16>] [vrfids WORD<0-512>]

Example

Note

The show ip spb-pim-gw mroute command displays active upstream information and active downstream information per (*,g) and (s,g) per port, which includes *G Join or Prune pending state, SG join or prune pending state, and SG Rpt PRUNE or PRUNE pending state.. There can be upstream information for a specific SG and no downstream, and vice-versa, as the information in the command show ip spb-pim-gw mroute reflects only information known on the SPB-PIM Gateway interfaces. For example, there might be downstream receivers on a SPB-PIM Gateway Interface for a particular stream which is ingressing on an spb-multicast interface; thus, the upstream information will not be displayed using this command.

Switch:1>show ip spb-pim-gw mroute
=============================================================================
              Spb-pim-gw Active PIM Multicast Route - GlobalRouter

=============================================================================

Src: 0.0.0.0       Grp: 225.1.1.1   
Flags: WC
Joined Ports:
Vlan     Ports            Join Timer           
----     -----            ---------            
Vlan30   1/3              155                  

-----------------------------------------------------------------------------

Src: 123.1.1.101   Grp: 225.1.1.1   Upstream: 50.1.1.1      Incoming Port: Vlan50-1/5

Flags: SG
SG Joined Ports:
Vlan     Ports            Join Timer           
----     -----            ---------            
Vlan30   1/3              184                  

SG Prune Pending Ports:
Vlan     Ports            Prune Pending Timer           
----     -----            ---------            
Vlan40   1/4              180                  

SG Rpt Pruned Ports:
Vlan     Ports            RPT Prune Timer           
----     -----            ---------            
Vlan90   1/9              156                  

SG Rpt Prune Pending Ports:
Vlan     Ports            RPT Prune Pending Timer           
----     -----            ---------            
Vlan60   1/6              164                  


-----------------------------------------------------------------------------
                    
Total Num of Entries Displayed 2/2
Flags Legend:
WC=(*,Grp) entry, SG=(Src,Grp) entry

Variable definitions

The following table defines parameters for the show ip spb-pim-gw mroute command.


Variable	Value
vrf`WORD<1-16>`	Displays the SPB-PIM Gateway mroute information for a specific VRF name.
vrfids `WORD<0-512>`	Displays the SPB-PIM Gateway interface mroute information for a range of VRF IDs. Note: Enter a single VRF ID or multiple VRF IDs separated by ‘,‘ or enter a range of VRF IDs ‘x-y‘.
group `{A.B.C.D}`	Displays mroute information specific to a group IP address.
source `{A.B.C.D}`	Displays mroute information specific to a source IP address.